1.Taiwan single point crane
Equipment overview
The Taiwan single-point hoist is a kind of hanging equipment with greater flexibility. It can combine several hoisting points together for synchronous operation or operate separately.
The driving device and lifting points of the Taiwan single-point hoist are all set at a fixed position above the orchestra outside the Taiwan. The hanging point is usually located in the ceiling, and when used, put it down to participate in the performance.
Each single point hoist has an independent driving device and transmission device, which can be operated at any speed.
The single-point hoist is composed of hooks, hoisting systems, control systems, detection and protection devices, and related supporting components. Detection and protection devices: stroke detection system, overshoot protection device, loose rope detection, job-hopping detection, load sensor, absolute encoder, etc.
Technical specifications: (can be customized according to requirements)
| size | / |
| Load | 2.5 KN |
| speed | 0.003～0.3m/s |
| Drive type | Electric wire rope winch |
2.Taiwan fire curtain
Equipment overview
The proscenium fire curtain is a special door for safety and fire protection. When a fire accident occurs in the theater or at the end of each performance, the fire curtain falls, separating the stage and the auditorium into two fireproof areas.
In an emergency, the fire curtain can be lowered into place by gravity within 45s after starting; when it is 2.5 meters away from the main stage surface, the damping starts to fall, and when it approaches the stage surface, it slows down again to avoid injury to people and impact on the stage surface. The fire resistance limit of the fire curtain conforms to the relevant national standards and can withstand the pressure difference between the auditorium and the stage due to fire.
There are running guide rails on both sides of the fire curtain, and sealing devices should be installed around the curtain body and the building wall so that the fire curtain can effectively seal smoke and fire when it is in the lowered position.
The operation panel with lifting, lowering and emergency stop buttons can realize local operation. The manual release mechanism is set on the inner side of the proscenium, and there is operation control and status display in the fire control room. The fire curtain is equipped with an anti-rushing device.
The fire curtain is composed of a curtain body, a guide rail, a counterweight, a winch system, a damping device, a protection device, and a sensor. Specifically:
ꞏThe curtain body is a steel frame with steel plate outsourcing and fire-retardant material filled inside.
ꞏThe winch system consists of a motor, a reducer, a brake, and a reel. With mechanical manual release device. The damping force and damping position of the released damping device are adjustable.
ꞏGuide rail and sealing device.
ꞏPulley assembly.
ꞏBalance weight and guide rail.
ꞏWire rope and accessories.
Set up warning lights and buzzers near the fire screen at the entrance. When the fire curtain descends, the buzzer sounds.
Technical specifications: (can be customized according to requirements)
| size | Proportion width+1m×High proscenium+0.5m×0.2m |
| Load | custom made |
| speed | 0.15m/s |
| Drive type | Electric wire rope winch with hydraulic damping |
3.Big screen machine
Equipment overview
The big screen set at the entrance of the stage has two different opening methods: side-by-side and lift-up. The two opening forms only allow one operation at a time, interlocking each other. It can be electrically driven, adjustable speed, and quick response to repeated operations.
The length of the overlapping part of the opening guide rail is 2m. The split mode has a manual opening function.
The big screen machine is composed of steel structure frame, guide rail, uniform shrinkage machine, transmission device, cable storage device, protection device and so on. Each form of opening (closing) screen realizes full stroke position and speed control.
Technical specifications: (can be customized according to requirements)
| size | Proportion width+6m |
| Load | Heavy curtain |
| speed | Lift：0.001～1.0m/s |
| Off：0.001～1.0m/s | |
| Drive type | Lifting: electric wire rope hoist |
| Off: electric wire rope traction |
4.Fake proscenium
Equipment overview
The false proscenium set on the inner side of the stage proscenium is composed of the top piece and the two side pieces. Adjust the size of the stage proscenium by changing the position of the upper and side films.
The steel structure of the false proscenium top piece and the two side pieces is easy to install stage lighting. At the same time, it provides convenience for the fixed setting of the follow spot light, which can be operated and used by people.
The false proscenium top piece is composed of steel frame, wire take-up basket, winch system, control system, protection device, etc.
The side pieces are located under the Taikou Steel Wharf and are electrically driven. They are arranged symmetrically and can move horizontally along the rails suspended under the wharf.
Technical specifications: (can be customized according to requirements)
Fake prosthetic movie
| size | Proportion width-3m×1.0m×4m |
| Load | custom made |
| speed | 0.001～0.1m/s |
| Drive type | Electric wire rope winch |
假台口侧片
| size | 3m×0.8m×High proscenium+1m |
| Load | 8 KN |
| speed | 0.1m/s |
| Drive type | electric |
5.Electric boom
Equipment overview
Set on the upper part of the main stage, it is used to elevate the scenery, various curtains and secondary screens, and can also hang lamps and lanterns. Electric booms also participate in performances.
The electric boom can be raised and lowered individually, or in groups or synchronously.
The electric boom is composed of a truss boom, a winch system, a control system and a protection device. Specifically, it consists of the following parts:
·Truss type boom with telescopic extension rods at both ends.
·Hoisting system: motor, reducer, brake, drum, pulley assembly, wire rope and accessories, etc.
·Protective devices: stroke detection system, overshoot protection device, loose rope detection, job-hopping detection, load sensor, absolute encoder, etc.
Technical specifications: (can be customized according to requirements)
| size | Proportion width+6m |
| Load | custom made |
| speed | 0.001～1.0m/s |
| Drive type | Electric wire rope winch |
6.Light boom
Equipment overview
A liftable electric light boom set on the upper part of the main stage for hanging lamps.
The light boom is composed of a truss-type pole, a winch system, a control system and a protection device. Specifically, it consists of the following parts:
ꞏTruss-type pole body with cable take-up device.
ꞏHoisting system: motor, gear box, brake, drum, pulley assembly, steel wire rope and accessories, etc.
ꞏDetection and protection devices: stroke detection system, overshoot protection device, loose rope detection, job-hopping detection, load sensor, absolute encoder, etc.
Technical specifications: (can be customized according to requirements)
| size | Proportion width+6m |
| Load | custom made |
| speed | 0.002～0.2m/s |
| Drive type | Electric wire rope winch |
7.Side light hanger
Equipment overview
The side light hangers set on both sides of the upper part of the main stage are specially used to install stage lamps to provide side light for the stage. On the lower edge of the triangular light stand, each hanger is equipped with a "eye"-shaped light rack for hanging lamps. The light rack can be manually moved in the vertical direction, and the triangle light rack can be raised and lowered as a whole.
Each set of "目"-shaped lighting rack is about 1.2m wide and 3.6m high. It can hang 4 rows of lamps up and down, and 2 lamps in each row. The bent frame is easy to disassemble and flexible to install.
The light boom is composed of a truss-type pole, a winch system, a control system and a protection device.
Specifically composed of the following parts：
ꞏTriangular truss type pole body, equipped with cable take-up device, "eye" type light frame.
ꞏHoisting system: motor, gear box, brake, drum, pulley assembly, steel wire rope and accessories, etc.
ꞏDetection and protection devices: stroke detection system, overshoot protection device, loose rope detection, job-hopping detection, load sensor, absolute encoder, etc.
Technical specifications: (can be customized according to requirements)
| size | / |
| Load | custom made |
| speed | 0.002～0.2m/s |
| Drive type | Electric wire rope winch |
8.Second curtain machine
Equipment overview
The second curtain machine can be hung on any boom and has the function of electric opening. It can also be opened manually in emergency. The stage can be divided into different performance areas or used as a backdrop. The second curtain machine is a device attached to the electric boom. The position of the second screen machine should be flexible and can be temporarily suspended according to the needs of users.
The overlapping part of the guide rail of the double-opening (closed) curtain should not be less than 2m, and the two sides should extend to allow the curtain to be doubled beyond the side curtain bars.
Technical specifications: (can be customized according to requirements)
| size | Proportion width+6m |
| Load | Heavy curtain |
| speed | 0.001～1.0m/s |
| Drive type | Electric wire rope traction |
9.Freestyle single point crane
Equipment overview
A free-style single-point hoist with a movable lifting point is installed on the top of the grid. The drive unit is fixed, and the lifting point is moved through freely rotatable steering wheels. The wire rope is output from the top layer of the grid through a lifting point that can be fixed at any position on the grid. The single-point hoist can be used to suspend three-dimensional stage scenery, and can also be used to provide a hanging point in the longitudinal direction of the stage or between two booms.
The free-style single-point hoist is composed of a hoisting system composed of a hook and an independent driving device, a trolley mechanism, a control system, a detection and protection device, and related supporting components.
Detection and protection devices: stroke detection system, overshoot protection device, loose rope detection, job-hopping detection, load sensor, absolute encoder, etc.
Technical specifications: (can be customized according to requirements)
| size | / |
| Load | 2.5 KN |
| speed | 0.001～1.0m/s |
| Drive type | Electric wire rope winch |
10.Automatic rope crane
Equipment overview
The self-arranging rope hoist adopts the integrated installation of the reel and the corner wheel group, which is used to drive the boom and other equipment.
Technical specifications: (can be customized according to requirements)
| size | / |
| Lifting load | 0~40 KN |
| speed | 0.001～1.0m/s |
11.Mechanical butterfly
The mechanical butterfly is an interactive device, and the butterfly wings can be automatically fanned and used as stage props.
Technical specifications: (can be customized according to requirements)
12.Integrated single point hoist
Equipment overview
The integrated single point hoist is used to drive stage props and other equipment.
Technical specifications: (can be customized according to requirements)
| size | / |
| Lifting load | 0~2.5 KN |
| speed | 0.001～1.0m/s |
13.Three-dimensional integrated boom
Equipment overview
The three-dimensional integrated boom can be used to hang lamps, LED screens, various scenery, etc., and can realize the lifting, translation and rotation of the boom.
| size | 0~5m |
| Load | 0~5KN |
| speed | Lift0.003~0.4m/s |
| Pan0.006~0.2m/s | |
| Spin0~3r/min | |
| Drive type | electric |
14.100kg crane
Equipment overview
The 100kg hoist can be set at any position on the top of the stage grid for hanging stage performances. Props, etc., rich
Technical specifications: (can be customized according to requirements)
| size | / |
| Lifting load | 0~1 KN |
| speed | 0.001～1.0m/s |
15.50kgcrane
Equipment overview
The 50kg crane can be set at any position on the top of the stage grid, used for hanging stage props, etc., enriching the stage performance
Technical specifications: (can be customized according to requirements)
| size | / |
| Lifting load | 0~0.5 KN |
| speed | 0.005～0.5m/s |
| Hanging points | 2 |
16.Side light cage
Equipment overview
The side light cages are set on both sides of the upper part of the main stage, and are dedicated to install stage lamps and lanterns to provide side light for the stage.
The side light cage can be operated by a person, can be raised and lowered vertically, or can be moved horizontally perpendicular to the direction of the platform. A ladder is installed inside to facilitate the installation of lamps and light, and there is a light cable storage device.
The side light cage is composed of the main steel structure frame, lifting device, translation device and control system. The lifting device and the translation device are composed of independent transmission devices and guide devices.
Technical specifications: (can be customized according to requirements)
| size | 1.2m×0.9m |
| Load | 6kN |
| speed | Lift：0.001～0.1m/s |
| Pan：0.001～0.1m/s | |
| Drive type | Lifting: electric wire rope hoist |
| Folio: Electric |
